 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| no. ld ? 19164a date jan } 22 } 2007 technical literature for tft - lcd module model no. LQ104S1LG61 the technical literature is subject to change without notice. so, please contact sharp or its representative before designing your product based on this literature. engineering department ? mobile lcd design center mobile liquid crystal disply group ? sharp corporation these p arts have corres p onded with the rohs directive. www.datasheet.co.kr datasheet pdf - http://www..net/
3 & $ 0 3 % 4 0 ' 3 & 7 * 4 * 0 / - 2 4 - ( 4 1 & $ / p % " 5 & 3 & 7 * 4 & % 4 6 . . " 3 : / 0 5 & / p 1 " ( & - % " + " / t u * t t v f www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 1. application this technical literature applies to color tft-lcd module, LQ104S1LG61 these technical literature sheets ar e the proprietary product of sharp corporation(?sharp) and include materials protected under copyright of sharp. do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. the device listed in these technical literature sheets wa s designed and manufactured for use in general electronic equipment. in case of using the device for applications such as control and safety equipment for transportation (conrrols of aircraft, trains, automobiles, etc.), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken. do not use the device for equipment that requires an extr eme level of reliability, such as aerospace applications, telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment for life support. sharp assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these technical literature sheets. confirm "12. handling precautions " item when you use the device. contact and consult with a sharp sales representative for any questions about this device. 2. overview this module is a color active matrix lcd module in corporating amorphous silicon tft (thin film transistor). it is composed of a color tft-lcd panel, driver ics, control circuit and power supply circuit and a backlight unit. graphics and texts can be displayed on a 8003600 dots panel with 262,144 colors by using lvds(l ow v oltage d ifferential s ignaling)system for interface and supplying +3.3v/5.0v dc supply voltage for tft-lcd panel driving and supply voltage for backlight. the tft-lcd panel used for this module is a low-reflection and higher-color-saturation type. therefore, this module is also suitable for the multimedia use this module is super-high brightness (420cd/m^2) and high contrast (500:1). this module is the type of wide viewingangle the viewing angle is 6 o?clock direction. backlight-driving dc/ac inverter is not built in this module. www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 3. outline specification. parameter specifications unit display size 26 (10.4") diagonal cm active area 211.2(h)158.4(v) mm pixel format 800(h)600(v) pixel (1 pixel=r+g+b dots) - number of colors (number of gray scale level) 262, 144 colors (64 gray scales per color) pixel pitch 0.264(h)0.264(v) mm pixel configuration r,g,b vertical stripe - display mode normally white - unit outline dimensions *1 246.5(w)179.4(h)max.15.5 (d) mm mass 620 (max) g surface treatment anti-glare and hard-coating 3h - *1: excluding backlight cables. outline dimensions is shown in fig.1 www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 4. input terminals 4-1. tft-lcd panel driving cn1 (lvds signals , +3.3v / +5.0v dc power supply and contorol signal) corresponding connector:fi-se2 0m (jae) or fi-s20s (jae) pin no. symbol function remark 1 v cc +3.3v / +5.0v power supply 2 v cc +3.3v / +5.0v power supply 3 gnd 4 gnd 5 rxin0- differential data input, ch0 (negative) lvds signal 6 rxin0+ differential data input, ch0 (positive) lvds signal 7 gnd 8 rxin1- differential data input, ch1 (negative) lvds signal 9 rxin1+ differential data input, ch1 (positive) lvds signal 10 gnd 11 rxin2- differential data input, ch2 (negative) lvds signal 12 rxin2+ differential data input, ch2 (positive) lvds signal 13 gnd 14 rxclk in- differential clock input (negative) lvds signal 15 rxclk in+ differential cloc k input (positive) lvds signal 16 gnd 17 r/l horizontal display mode select signal [note1] 18 u/d vertical display m ode select signal [note2] 19 gnd 20 gnd [note ] to obtain the proper relation between lvds signals and actual digital data signals, the digital signals should be inputted into the transmitter as described in the nextsection, 4-2. [note ] the shielding case is connected with signal gnd. [note ] data mapping d z d m f ( 3 3 3 3 3 3 3 3 ( # # ( ( ( ( ( ( ( # % & # # # # # # % & 7 4 ) 4 3 9 * / 3 9 * / 3 9 * / 3 9 $ - , * / www.datasheet.co.kr datasheet pdf - http://www..net/ - % " [note 1],[note 2] r/l = high, u/d = low r/l = low, u/d = low r/l = high, u/d = high r/l = low, u/d = high www.datasheet.co.kr datasheet pdf - http://www..net/ - % " using receiver single lvds interface, which equals thc63lvdf64a(thine),contained in a control ic corresponding transmitter ds90c363, ds90c363a, ds90c383, ds90c383a national semiconductor thc63lvdf63a,thc63lvdm63a(thine), sn75lvds84(ti) 4-2 lvds interface block diagram system side ( tft-lcd side) 100 100 100 10uf r0 ? r5 b0 ? b5 hsync v sync enab g0 ? g5 ck lvds transmitter rxin1+ (9pin) rxin1- (8pin) rxin2+ (12pin) rxin2- (11pin) rxclkin+ (15pin) rxclkin- (14pin) lvds receiver controller r/l u/d 10k 10k r0 ? r5 b0 ? b5 hsync vsync enab g0 ? g5 cl k r/l u/d vcc + rxin0+ (6pin) rxin0- (5pin) 100 100 100 txin18 txin19 txin20 txclk in txin 0 ? 5 txin 6 ? 11 txin12 ? 17 pll digital signal lv d s si g n a l rxout18 rxout19 rxout20 rxclk out rxout12 ? 17 rxout6 ? 11 rxout0 ? 5 pll lv d s si g n a l digital signal r/l(17pin) u/d(18pin) vcc(1,2pin) gnd gnd gnd(3,4,7,10,13,16,19,20pin) ld19164a-5 www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 4-3. backlight driving cn2 ,cn3 used connector : bhr-02(8.0)vs-1n (jst) corresponding connector : sm02(8.0)b-bhs-1-tb or -1n-tb (jst) pin no. symbol function color of fl cable 1 vhigh power supply for lamp (high voltage side) (orange) ? (blue) 2 vlow power supply for lamp (low voltage side) (white) ? (gray) 5. absolute maximum ratings parameter symbol condition pin name ratings unit remark +3.3v / +5.0v supply voltage vcc ta=25 o c vcc 0 to + 6.0 v input voltage vi1 rxini-/+(i= 0,1,2) -0.3 to vcc+0.3 v vcc 3.0v ta=25 o c rxclk in-/+ -0.3 to 3.3v v 3.0v ? vcc vi2 ta=25 o c r/l , u/d -0.3 to vcc+0.3 v lamp input voltage vhigh - - 1800 vrms storage temperature tstg - - -30 to +80 o c operating temperature topa panel surface - -30 to +80 o c [note1] [note1] humidity: 95%rh max. at ta ? 40 o c. maximum wet-bulb temperature at 39 o c or less at ta>40 o c. no condensation. 6. recommended operation condition parameter symbol min. typ. max. unit remark supply voltage vcc 3.0 +3.3/+5.0 5.5 + [note1] lvds signals v l 0 2.4 + [note2] input voltage vi 0 vcc + [note3] ambient temperature topa -30 +80 ? [note4], [note5] [note1] vcc-turn-on conditions 0 - % " 7. electrical characteristics 7-1. tft-lcd panel driving ta=25 o c parameter symbol min. typ. max. unit remark vcc=+3.3v icc - 300 450 ma current dissipation vcc=+5.0v icc - 200 300 ma [note1] permissive input ripple voltage vrp - - 100 mvp-p input voltage range lvds signal vl 0 - 2.4 v [note2] differential input high vth - - vcm+ 100 mv v cm =1.2v threshold voltage low vtl vcm? 100 - - mv [note3] input impedance (differential input) rt - 100 - [note2] low vil - - 0.8 v [note4] input voltage high vih 2.1 - - [note5] low(vi=0v) iol1 -800 - - ua input current1 high(vi=vcc) ioh1 -10.0 - 10.0 ua [note4] low(vi=0v) iol2 -10.0 - 10.0 ua input current2 high(vi=vcc) ioh2 - - 800 ua [note5] [note1] typical current situation : 16-gray-bar pattern. vcc=+3.3v / +5.0v [note2] lvds signals [note3] v cm : common mode voltage of lvds driver. [note4] r/l [note5] u/d 3 ( # ( 4 3 ( # ( 4 3 ( # ( 4 3 ( # ( 4 3 ( # ( 4 www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 7-2. backlight driving the backlight system is an edge-lighting type with double ccft (cold cathode fluorescent tube). the characteristics of single lamp are shown in the following table. (it is usually required to measure under the following condition. il=6.0ma,ta=25 ?? 2 ? ,fl=60khz.) parameter symbol min. typ. max. unit remark lamp current il 3.0 6.0 6.5 ma rms [note1] lamp power consumption pl - 3.5 - w [note2] lamp frequency fl 35 60 70 khz [note3] kick-off voltage vs - - 1300 inverter output [note4] - - (2000) v rms (transformer output) ta=-30 o c 50000 - - hour il=6.0marms[note5] lamp life time ll 60000 hour il=5.0marms[note5] [note1] lamp current is measured with current meter for high frequency as shown below. [note2] referential data per one ccft by calculation. (i l vl) the data don?t include loss at inverter. ( il=6.0marms) [note3] lamp frequency may produce interference with horizontal synchronous frequency,and this may cause beat on the display. therefore lamp frequency shall be detached as much as possible from the horizontal synchronous frequency and from the harmonics of horizontal synchronous to avoid interference. [note4] the open output voltage of the inverter shall be maintained for more than 1s; otherwise the lamp may not be turned on. [note5] above value is applicable when lamp (the long side of lcd module) is placed hor izontally. (landscape position) lamp life time is defined that it applied either ? or ? under this condition (continuous turning on at ta=25 o c, il=6.0ma rms) ? brightness becomes 50% of the original value under standard condition. ? kick-off voltage at ta=-30 o c exceeds maximum value, 1300vrms. lamp life time shortens according to the state of mounting and use. (lamp lifetime may vary if lamp is in portrait position du e to the change of mercury density inside the lamp.) in case of operating under lower temp environment, the lamp exhaustion is accelerated and the brightness becomes lower. (continuous operating for around 1 month under lower temp condition may reduce the brightness to half of the original brightness.) in case of such usage under lower temp environm ent, periodical lamp exchange is recommended. [note6] the performance of the backlight, for example life time or brightness, is much infl uenced by the characteristics of the dc-ac inverter for the lamp. when you design or order the inverter, please make su re that a poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting,flicker, etc.) never occur. when you confirm it, the module should be operated in the same condition as it is installed in your instrument. be sure to use a back light power supply with the safe ty protection circuit such as the detection circuit for the excess voltage, excess current and or electric discharge waveform. be sure to use the detect circuit by which one side of the ccft lamps can be controlled independently. otherwise, when one side of the ccft is open, the excess current may possibly be applied to the other side of the lamp. recommended inverter is ?cxa-0454 (tdk)?. ( ? cxa-p1212b-wjl(tdk) ? is also recommended under general temperature condition.) [note7] it is required to have the inverter designed so that to allow the impedance deviation of the two ccft lamps and the capacity deviation of barast capacitor. [note8] under the environment of 10lx or less, miss-lighting delay may occur. module ? + ? transformer output voltage inverter output voltage cn2,3 2pin + ? cn2,3 1pin inverter www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 8. timing characteristics of input signals 8-1. timing characteristics (these are specified at the digital inputs/outputs of lvds transmitter/receiver.) data enab sync a b d e f c (vertical timing) item(symbol) min. typ. max. unit ?? vsync cycle (t va ) - 17.6 - ms negative 628 666 798 line blanking period(t vb ) 28 66 - line vsync pulse width (t vc ) 2 4 6 line back porch (t vd ) 23 23 23 line vsync pulse width+back porch (t vc +t vd ) 25 27 29 line active display area (t ve ) 600 600 600 line front porch (t vf ) 3 39 - line (horizontal timing) item(symbol) min. typ. max. unit remark hsync cycle (t ha ) 20.8 26.4 39.9 us negative 832 1056 1395 clock blanking period (t hb ) 40 256 - clock hsync pulse width (t hc ) 2 128 200 clock back porch (t hd ) 928-t ha 88 t ha -752 clock active display area (t he ) 800 800 800 clock front porch (t hf ) 0 40 - clock (clock signal) item min. typ. max. unit remark frequency 35 40 42 mhz [note1] [note1] in case of lower frequency, the deterioration of display quality, flicker etc., may be occurred. (hsync-vsync phase difference) t hv vsync hsync item(symbol) min. typ. max. unit remark hsync-vsync phase difference (t hv ) 1 - t ha -t hc clock www.datasheet.co.kr datasheet pdf - http://www..net/ - % " (hsync-enab phase difference) enab hsync t hn item min. typ. max. unit remark hsync-enab phase difference (t hn ) 0 - t ha -t hc -800 clock 8-2 display position item standards beginning ending unit remark horizontal rising edge of enab 0 800 clock rising edge of hsync 88 888 clock [note1] vertical rising edge of vsync 23 623 line [note1] in case that enab signal is fixed to lo w level. do not keep enab signal high during operation. 8-3. input data signals and display position on the screen d1,dh1 d1,dh2 d1,dh3 d2,dh2 d2,dh1 d3,dh1 r g b display position of input data ( h , v *% d800, d1,dh600 d800,dh1 dh600 www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 9. input signals, basic display colors and gray scale of each color 0 :low level voltage, 1 : high level voltage each basic color can be displayed in 64 gray scales from 6 bit da ta signals. according to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen. colors & data signal gray scale gray scale r0 r1 r2 r3 r4 r5 g0 g1 g2 g3 g4 g5 b0 b1 b2 b3 b4 b5 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 black gs0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 gs1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 darker gs2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? brighter gs61 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 ? gs62 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 red gs63 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 black gs0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 gs1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 darker gs2 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 ? brighter gs61 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0 ? gs62 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 green gs63 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 black gs0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 gs1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 darker gs2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 ? brighter gs61 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 ? gs62 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 blue gs63 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 basic color gray scale of red gray scale of green gray scale of blue www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 10. optical characteristics ta=25 ? , vcc=+3.3v / +5.0v parameter symbol condition min. typ. max. unit remark viewing horizontal 21, 22 cr>10 60 70 - deg. [note1] angle vertical 11 35 50 - deg. [note4] range 12 55 60 - deg. contrast ratio crn =0 o 300 - - [note2] cro optimum viewing angle - 500 - [note4] response rise r - 10 - ms [note3] time decay d - 25 - ms [note4] chromaticity of white x 0.263 0.313 0.363 y 0.279 0.329 0.379 x 0.546 0.596 0.646 chromaticity of red y 0.279 0.329 0.379 x 0.260 0.310 0.360 chromaticity of green y 0.502 0.552 0.602 x 0.117 0.167 0.217 chromaticity of blue y 0.132 0.182 0.232 [note4] il=6.0marms f=60khz luminance of white y l1 330 420 - cd/m 2 white uniformity w =0 o - - 1.35 [note5] [note] the measurement shall be executed 30 minutes after lighting at rating. (condition:il=6.0ma rms) the optical characteristics shall be measured in a dark room or equivalent state with the method shown in fig.3 below. photodetector fig.3 optical characteristics measurement method center of the screen tft-lcd module 400mm field 1 1 ? lcd panel viewing angle/response time : bm-5a (topcon) contrast ratio/luminance of white/chromaticity : sr-3(topcon) www.datasheet.co.kr datasheet pdf - http://www..net/ - % " [note1] definitions of viewing angle range: n orm al line 12 ? e). 11. display quality the display quality of the color tft-lcd module shall be in compliance with the incoming inspection standard. luminance (brightness) with all pixels white luminance (brightness) with all pixels black maximum luminance of five points (brightness) minimum luminance of five points (brightness) x1 a b c d e p ixel 200 400 600 pixel 150 300 450 www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 12.handling precautions a) be sure to turn o ff the power supply when inserting or disconnecting the cable. b) be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. c) since the front polarizer is easily damaged, pay attention not to scratch it. blow away dust on the po larizer with antistatic # 2 blow. it is undesirable to wipe off because a polarizer is sensitive. it is recommended to peel off softly using the adhesive tape when soil or finger oil is stuck to the polarizer. when unavoidable, wipe off carefully with a cloth for wiping lenses. d) wipe off water drop immediately. long contact with water may cause discoloration or spots. e) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. f) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. handle with care. g) since cmos lsi is used in this module, take care of static electricity and injure the human earth when handling. observe all other precautionary requirements in handling components. h) since there is a circuit board in the module back, stress is not added at the time of a design assembly. please make it like. if stress is added, there is a possibility that circuit parts may be damaged. i) protection film is attached to the modu le surface to prevent it from being scratched . peel the film off slowly , just before the use, with strict attention to electrostatic charges. blow off 'dust' on the polarizer by using an ionized nitrogen. j) the polarizer surface on th e panel is treated with anti-glare for low reflection. in case of attaching protective board over the lcd, be careful about the optical interface fri nge etc. which degrades display quality. k) do not expose the lcd panel to direct sunlight. lightproof shade etc. should be attached when lcd panel is used under such environment. l) connect gnd to 4 place of mounting holes to stabilize against emi and external noise. m) there are high voltage portions on the backlight and very dangerous. careless touch may lead to electrical shock. when exchange lamps or service, turn off the power without tail. n) when handling lcd modules and assembling them into cabinets, please be noted that long-term storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent,solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the lcd modules. o) cold cathode fluorescent lamp in lcd panel contai ns a small amount of mercury, please follow local ordinances or regulations for disposal. p) be careful of a back light lead not to pull by force at the time of the wiring to an inverter, or line processing. q) when install lcd modules in the cabinet, recommended torque value is ?0.294 ? 0.02n k m (3.0 ? 0.2kgf k cm)?. be sure to confirm it in the same co ndition as it is installed in your instrument. r) liquid crystal contained in the pane l may leak if the lcd is broken. rinse it as soon as possible if it gets inside your eye or mouth by mistake. s) notice:never dismantle the module , because it will cause failure. t) be careful when using it for long time with fi xed pattern display as it may cause afterimage. u) adjusting volume have been set optimally before shipment, so do not change any adjusted value. if adjusted value is changed, the specification may not be satisfied. v) if a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity issue, etc. therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan. w)the lamp used for this product is very sensitive to the temperature. luminance decreases rapidly when it is used for a long time or repeatedly under the environment of the low temperature or the module is being cooled. please avoid the continuous or repeating use of it under such an environment. it may decrease up to 50% of the initial luminance in about one month under the low temperature environment. please consult our company when it is used under the environment like the above mentioned. www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 13. packing form product countries / areas japan taiwan china piling number of cartons 6 package quantity in one carton 10pcs carton size 395(l)310(w)270(h) total mass of one carton filled with full modules 8,000g packing form is shown fig2 14.reliability test items no. test item conditions remark 1 high temperature storage test ta=80 ? 240h 2 low temperature storage test ta= -30 ? 240h 3 high temperature & high humidity operation test ta=40 ? ; 95%rh 240h (no condensation) 4 high temperature operation test tp=80 ? 240h panel surface 5 low temperature operation test ta= -30 ? 240h 6 vibration test (non- operating) frequency: 10 ? 57hz/vibration width (one side ): 0.115mm : 57 ? 500hz/gravity: 14.7 m/s 2 sweep time : 11 minutes test period : 3 hours (1 hour for each direction of x,y,z) 7 shock test (non- operating) max. gravity : 490m/s 2 pulse width : 11ms, half sine wave direction : ? x, ? y, ? z once for each direction. 8 esd test human model 9 emi measurement in 10m site display position on the screen = ? h ? (full-screen), gnd to 4 place = un-connect, vcc / vsignal = typ. vcci (class b) [result evaluation criteria] under the display quality test conditions with normal operation state, these shall be no change which may affect practical di splay function. (nor mal operation state temperature:15 ? 35 ? , humidity:45 ? 75 ? , atmospheric pressure:86 ? 106kpa) www.datasheet.co.kr datasheet pdf - http://www..net/ - % " 15.others 15-1 lot no. label: model number made in japan made in taiwan japan taiwan product countries / areas made in china china serial no. (5 digits) production year (last digit of dominical year) production month (1-9x, y, z) assembly site code lot number } ? 4 1 3 barcode barcode - 2 4 - ( * * discernment code 15-2 packing box label: t o ? j ( LQ104S1LG61 !>c#$} ) } } &d0=c8ch & ?2b a?2 ? j barcode barcode barcode 3?? v;???pb{ model number lot number (date) quantity of module type quantity date LQ104S1LG61 10pcs 2007. 2. 1 quantity of module : japan or china quantity of module : taiwan LQ104S1LG61g t r.c. rohs compliance means these parts have corresponded with the rohs directive. 15-3 if any problem occurs in relation to the description of this technical literature sheets, it shall be resolved through discussion with spirit of cooperation. ' * o u f s o b m 6 t f 0 o m z www.datasheet.co.kr datasheet pdf - http://www..net/ www.datasheet.co.kr datasheet pdf - http://www..net/ www.datasheet.co.kr datasheet pdf - http://www..net/ |
Price & Availability of LQ104S1LG61
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |